• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Interface with a PC via RS-232 or USB connection
• Remote control available using analog communication—voltage, current and contact closure
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy

• Flow range 0.18 to 65 ml/min—low rate depends on drive rpm and 4- or 6-mm OD tubing
• Rigid pump tubing designed to pump fluids at pressures up to 100 psi (6.9 bar)
• Adjustable occlusion—tighten for higher pressure, loosen for longer tubing life
• Limited chemical exposure with PTFE tubing as only wetted part

• Convex-roller design is gentler on live cells and shear-sensitive fluids—validated by independent test data
• Large-diameter rotor delivers higher flow rates at lower speeds
• Low-speed pumping lets you maintain the consistency and characteristics of shear-sensitive fluids
• Drive housings are completely sealed—IP66 and NEMA 4X rated—simply hose down to clean
• Brushless, maintenance-free motor offers ±0.1% speed control accuracy with a 6000 to 1 turndown ratio
• Cytoflow pump head offers the best option for pumping live cells and shear-sensitive fluids--validated by independent test data
• Full remote control capabilities allow easy integration into automated processes
• Graphical LCD shows four operating modes continuous run, timed dispense, copy dispense, volume dispense. View pump performance continually

• Separate motor and controller are connected via a 6-ft (1.9 m) cable — place components where convenient or where space allows
• Single-turn speed control and on/off switch with green power indicator — maintain speed setting while turning pump on/off
• The 1/10-hp reversible motor has soft start and back EMF for ±2% speed control
• Painted steel housing is IP33 rated for protection from vertically falling water

• Flow range 3.6 to 3400 ml/min—low rate depends on drive rpm, tubing head, and tubing size
• Easily vary speed by adjusting air pressure with regulator
• Rugged 3/4-hp air motor requires little maintenance and generates less heat than an electric motor
• IP44 rated—painted steel housing protects from gentle spray

• Flow rate 1.8 to 220 ml/min with L/S tubing—flow rate depends on drive rpm, pump head, and tubing size
• Pump head accepts continuous lengths of tubing for clean flow paths
• Dual-channel model delivers synchronous flow from two separate channels; single-channel model delivers highest flow rate
• Automatic tubing retention makes tube loading quick and easy
• Separate single-turn speed control and forward/off/reverse switch—maintain speed setting when turning pump on or off
• Remote start/stop via contact closure on back of pump

• Flow range 0.004 to 315 ml/min with included L/S tubing—flow rate depends on drive rpm, pump head, and tubing size
• Digital interface with graphical LCD shows pump performance and operating mode
• Remote control available using analog communication—voltage, current and contact closure
• Integrated “open-head” sensor halts operation when pump head is opened
• Pump head accepts continuous lengths of tubing for clean flow paths
• Automatic tubing retention makes tube loading quick and easy
• More than 20% smaller than competitive units—compact size and light weight make it easy to move and share between labs

• Flow rate 0.9 to 90 ml/min (depends on drive rpm and tubing size)
• Four digit LED display shows motor rpm—confirm speed setting at a glance
• Integrated open-head sensor stops drive motor when pump head is opened
• Reversible motor—purge tubing before or after pumping; pump fluid in either direction
• LED indicators confirm motor direction
• Powerful motors let you stack 2 or 4 pump heads for increased flow rates and for multichannel applications
• Separate speed and power (on/off) control—maintain speed setting while turning pump on/off
• NEMA 4X (IP66) rated housing
• Remote control capabilities via a watertight connector on back of drive
• High-Performance pump head offers automatic occlusion—optimized when pump head is closed and latched

• Simple operation with single-turn speed control
• Separate power switch enables you to maintain speed setting when turning drive on/off; front-panel LED indicates power on
• Reversible motor lets you easily prime/purge tubing and pump in either direction
• Remote control of start/stop via DB9 connector on back of drive

• Precise, repeatable performance that is quick and easy to set up and program
• 5” (12.7 cm) capacitive TFT/RGB touch screen for crisp resolution and a wide viewing angle
• Pump lets you save and retrieve commonly used dispense programs for rapid set up
• Over-the-air firmware updates let you take full advantage of improvements in drive features and functionality
• Options for connectivity and monitoring include MasterflexLive, EtherNet/IP™, Profibus, or analog signal
• Three-level user access – gives you the option of controlling who can operate the pump and at what level.
• Continuous run, volume dispense, and time dispense modes -- batch control and interval/off time in Volume and Time modes
• Anti-drip and speed ramping available in Volume dispense mode – ensure accuracy, minimize sample loss, and eliminate foaming

• Flow rate 0.06 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm and tubing size
• Three digit LED display shows motor rpm — confirm speed setting at a glance
• Reversible motor—purge tubing before or after pumping; pump fluid in either direction
• LED indicators confirm motor direction
• Choose between benchtop controller or washdown wall-mount controller drives

• Flow rate 0.001 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm pump head, and tubing size
• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Remote control available using analog communication—voltage, current and contact closure
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy
• Models with open-head sensor stops the drive when the pump head is opened

• Accurate and repeatable settings with 3-digit LED display of rpm
• Pump fluid in either direction with reversible motor—perfect for purging tubing
• Choose multichannel systems for synchronous flow from all channels
• Maximize processes in a minimal footprint by stacking splash-resistant, IP33-rated drives
• Two ways to control speed, direction, and start/stop—use either the membrane keypad or remote-control capabilities

• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Remote control available using analog communication—voltage, current and contact closure
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy
• Models with open-head sensor stops the drive when the pump head is opened (when used with sensor-equipped pump head)
• NEMA 4X (IP66) rated housing for washdown applications
• Models with open-head sensor stop drive motor when pump head is opened

• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Remote control available using analog communication—voltage, current and contact closure
• Select your preferred language from the user-friendly menu for programming and operation
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy
• Brushless, maintenance-free motor offers ±0.1% speed control accuracy with a 6000 to 1 turndown ratio
• Reversible motor—purge tubing before or after pumping or pump fluid in either direction
• Powerful motors let you stack pump heads for increased flow rates and for multichannel applications

• Four digit LED display shows motor rpm—confirm speed setting at a glance
• Integrated open-head sensor stops drive motor when pump head is opened
• Reversible motor—purge tubing before or after pumping; pump fluid in either direction
• LED indicators confirm motor direction
• Powerful motors let you stack 2 or 4 pump heads for increased flow rates and for multichannel applications
• Separate speed and power (on/off) control—maintain speed setting while turning pump on/off
• NEMA 4X (IP66) rated housing
• Remote control capabilities via a watertight connector on back of drive

• Flow rate 0.28 to 1700 ml/min with included L/S tubing—flow rate depends on drive rpm, pump head, and tubing size
• Digital interface with graphical LCD shows pump performance and operating modes—continuous run, timed dispense, copy dispense, or volume dispense
• Select your preferred language from the user-friendly menu for programming and operation
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)Antidrip function ensures dispensing accuracy
• Brushless, maintenance-free motor offers ±0.1% speed control accuracy with a 6000 to 1 turndown ratio

• Digital interface with graphical LCD shows pump performance and operating modes—continuous run, timed dispense, copy dispense, or volume dispense
• Select your preferred language from the user-friendly menu for programming and operation
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)Antidrip function ensures dispensing accuracy
• Brushless, maintenance-free motor offers ±0.1% speed control accuracy with a 6000 to 1 turndown ratio
• Models with open-head sensor stop drive motor when pump head is opened

• Flow rate 0.06 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm, pump head, and tubing size
• Simple operation with single-turn speed control
• Separate motor and controller are connected via a 6-ft (1.9 m) cable — place components where convenient or where space allows
• Single-turn speed control and on/off switch with green power indicator — maintain speed setting while turning pump on/off
• The 1/10-hp reversible motor has soft start and back EMF for ±2% speed control
• Painted steel housing is IP33 rated for protection from vertically falling water

• Flow rate 0.06 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm and tubing size
• Three digit LED display shows motor rpm — confirm speed setting at a glance
• Reversible motor—purge tubing before or after pumping; pump fluid in either direction
• LED indicators confirm motor direction
• Splash-resistant ABS plastic controller housing is IP33
• rated
• Remote control capabilities via a DB9 female connector on back of controller

• Flow rate 0.06 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm and tubing size
• Three digit LED display shows motor rpm — confirm speed setting at a glance
• Reversible motor—purge tubing before or after pumping; pump fluid in either direction
• LED indicators confirm motor direction
• Wall-mount controller housing is powder-coated aluminum, IP66/NEMA 4X rated for washdown
• Remote control capabilities via weather-resistant connection on controller

• Flow rate 0.06 to 3400 ml/min (depends on drive rpm and tubing size)
• Four digit LED display shows motor rpm—confirm speed setting at a glance
• Integrated open-head sensor stops drive motor when pump head is opened
• Reversible motor—purge tubing before or after pumping; pump fluid in either direction
• LED indicators confirm motor direction
• Powerful motors let you stack 2 or 4 pump heads for increased flow rates and for multichannel applications
• Separate speed and power (on/off) control—maintain speed setting while turning pump on/off
• NEMA 4X (IP66) rated housing
• Remote control capabilities via a watertight connector on back of drive

• Economy fixed-speed drives are stackable and ideal for lab, field, or process feed applications
• Choose from seven speeds based on flow rate or number of heads required
• Constructed with painted steel housing for IP22-rating

• Flow rate 0.006 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm pump head, and tubing size
• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Remote control available using analog communication—voltage, current and contact closure
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy
• Models with open-head sensor stops the drive when the pump head is opened (when used with sensor-equipped pump head)
• NEMA 4X (IP66) rated housing for washdown applications

• Flow rate 2.1 to 560 ml/min—flow rate depends on drive rpm, pump head, and tubing size
• Stackable, compact drive is perfect for small work areas
• Constructed with a painted steel housing with IP22 rating
• No difficult programming—single switch for forward/off/reverse and analog controller
• Pump in either direction—also allows purging before or after pumping
• Remote control of start/stop via contact closure

• Flow rate 0.001 to 3400 ml/min with L/S tubing—flow rate depends on drive rpm pump head, and tubing size
• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Remote control available using analog communication—voltage, current and contact closure
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy
• Models with open-head sensor stops the drive when the pump head is opened (when used with sensor-equipped pump head)

• Flow rate 0.42 to 2900 ml/min with L/S tubing—flow rate depends on drive rpm, pump head, and tubing size
• Simple operation with single-turn speed control
• Separate power switch enables you to maintain speed setting when turning drive on/off; front-panel LED indicates power on
• Reversible motor lets you easily prime/purge tubing and pump in either direction
• Remote control of start/stop via DB9 connector on back of drive

• Powerful, space-efficient drives will accept all L/S pump head and tubing options
• 5” (12.7 cm) capacitive TFT/RGB touch screen for crisp resolution and a wide viewing angle
• Pump lets you save and retrieve commonly used dispense programs for rapid set up
• Over-the-air firmware updates let you take full advantage of improvements in drive features and functionality
• Options for connectivity and monitoring include MasterflexLive, EtherNet/IP™, Profibus, or analog signal
• Three-level user access – gives you the option of controlling who can operate the pump and at what level.
• Continuous run, volume dispense, and time dispense modes -- batch control and interval/off time in Volume and Time modes
• Anti-drip and speed ramping available in Volume dispense mode – ensure accuracy, minimize sample loss, and eliminate foaming

• Flow range 3.6 to 3400 ml/min—low rate depends on drive rpm, tubing head, and tubing size
• Easily vary speed by adjusting air pressure with regulator
• Rugged 1/3-hp air motor requires little maintenance and generates less heat than an electric motor
• IP44 rated—painted steel housing protects from gentle spray

• Cartridges snap in and out for fast tubing changes—no need to remove pump head from the drive
• Improved retainer design holds tubing securely in place
• Flow rate 0.00006 to 85 ml/min with microbore 2-stop tubing—flow rate depends on drive rpm, cartridge, and tubing size
• Accepts up to 4 large cartridges
• Require drives with a minimum of 1⁄10 hp and a maximum of 250 rpm
• Constructed with 8 Rulon® rollers, stainless steel rotor, and PSF ends

• New design and automatic tubing retention allow for multiple tubing sizes—change tubing without removing head from drive
• Rotor is constructed of stainless steel (SS) for enhanced durability
• Pump heads are stackable for multichannel applications
• Compact design for efficient use of space
• Suitable for use with L/S® High-Performance Precision pump tubing sizes

• Cartridges snap in and out for fast tubing changes—no need to remove pump head from the drive
• Improved retainer design holds tubing securely in place
• Flow rate 0.0008 to 350 ml/min with L/S tubing—flow rate depends on drive rpm, cartridge, and tubing size
• Accepts up to 2 large cartridges
• Require drives with a minimum of 1⁄10 hp and a maximum of 250 rpm
• Constructed with 6 Rulon® rollers, stainless steel rotor, and PSF ends

• Cartridges snap in and out for fast tubing changes—no need to remove pump head from the drive
• Improved retainer design holds tubing securely in place
• Flow rate 0.00017 to 170 ml/min with L/S tubing—flow rate depends on drive rpm, cartridge, and tubing size
• Accepts up to 6 large cartridges
• Require drives with a minimum of 1⁄10 hp and a maximum of 600 rpm
• Constructed with 6 Rulon® rollers, stainless steel rotor, and PSF ends

• New design and automatic tubing retention allow for multiple tubing sizes—change tubing without removing head from drive
• Four-roller rotor improves pressure performance and mechanical stability while reducing pulsation
• Compact design for efficient use of space
• Suitable for use with L/S® Precision pump tubing sizes

• Flow range 0.06 to 2300 ml/min—flow rate depends on drive rpm and tubing size
• Twist-lock mounting feature lets you mount and stack heads in seconds
• Included mounting plate adapts Easy-Load® 3 to L/S drives — locking tab secures pump head during operation in either direction
• Same side tubing entry/exit permits easy integration into space-limited applications — mount and operate pump head in any of four positions—depending on drive
• Suitable for use with Masterflex® L/S® Precision tubing

• PTFE and glass wetted parts help maintain fluid purity
• Ideal for pumping through filters or into pressurized systems
• Check valve on inlet side of pump holds prime for up to two hours when pump is off

• New design and automatic tubing retention allow for multiple tubing sizes—change tubing without removing head from drive
• Four-roller rotor improves pressure performance and mechanical stability while reducing pulsation
• Model available with integrated open-head sensor–connects directly to sensor-equipped drives
• Pump heads are stackable for multichannel applications
• Compact design for efficient use of space
• Suitable for use with L/S® High-Performance Precision pump tubing sizes

• Tubing occlusion is automatic and optimized when pump head is closed and latched – load tubing in 15 seconds or less
• Flow rates up to 3400 ml/min—flow rate depends on drive rpm, pump head, and tubing size
• Pressure up to 150 psi (10.3 bar) with L/S high-pressure (HP) pump tubing
• Reinforced nylon housing and occlusion bed with stainless steel rotor/roller assembly
• Compatible with all 1/10 hp L/S drives that accept two or more pump heads
• Compact design for efficient use of space

• Cartridges snap in and out for fast tubing changes—no need to remove pump head from the drive
• Load pump heads with 1 to 8 cartridges
• Mix large and small cartridges—one large cartridge occupies the same space as two small ones
• Flow rate 0.047 to 1400 ml/min with microbore or L/S tubing—flow rate depends on drive rpm, cartridge, and tubing size
• Accepts 1 to 8 small or 1 to 4 large cartridges
• Require drives with a minimum of 1⁄10 hp and a maximum of 600 rpm
• Constructed with stainless steel rotor and bearings with polysulfone ends

• Flow range 0.045 to 2300 ml/min per channel— flow rate depends on drive rpm and tubing size
• Stainless steel (SS) rotor / roller for greater durability and chemical resistance
• Stackable two-, four-, or eight-channel heads for up to 24 channels
• Simple tubing installation—lLoad the tubing, latch the occlusion bed, and run the pump

• PTFE tubing is the only wetted part ensuring fluid purity and excellent chemical compatibility
• Delivers a wide range of flow rates at pressures up to 100 psi (6.9 bar)
• Six-roller pump head with adjustable occlusion—tighten occlusion for higher pressure, loosen for longer tubing life

• Cartridges snap in and out for fast tubing changes—no need to remove pump head from the drive
• Improved retainer design holds tubing securely in place
• Flow rate 0.00001 to 41 ml/min with microbore 2-stop tubing—flow rate depends on drive rpm, cartridge, and tubing size
• Accepts up to 12 large cartridges
• Require drives with a minimum of 1⁄10 hp and a maximum of 600 rpm
• Constructed with 8 Rulon® rollers, stainless steel rotor, and PSF ends

• Order optional minicartridges with adjustable occlusion to vary pressure each channel
• Easily remove or insert minicartridges without disturbing other channels
• Max pressure of 1.5 bar is achieved with pressure-lever cassettes only
• Click-n-go cassettes offer a max pressure of 1.0 bar.

• New design and automatic tubing retention allow for multiple tubing sizes—change tubing without removing head from drive
• Rotor is constructed of stainless steel (SS) for enhanced durability
• Pump heads are stackable for multichannel applications
• Compact design for efficient use of space
• Suitable for use with L/S® Precision pump tubing sizes

• New design and automatic tubing retention allow for multiple tubing sizes—change tubing without removing head from drive
• Four-roller rotor improves pressure performance and mechanical stability while reducing pulsation
• Model available with integrated open-head sensor–connects directly to sensor-equipped drives
• Pump heads are stackable for multichannel applications
• Compact design for efficient use of space

• Flow range 1.7 to 2900 ml/min—flow rate depends on drive rpm and tubing size
• Twist-lock mounting feature lets you mount and stack heads in seconds
• Included mounting plate adapts Easy-Load® 3 to L/S drives — locking tab secures pump head during operation in either direction
• Same side tubing entry/exit permits easy integration into space-limited applications — mount and operate pump head in any of four positions—depending on drive
• Suitable for use with Masterflex® L/S® High-Performance Precision tubing

• Flow range of 1.8 to 220 ml/min—flow rate depends on drive rpm, pump head, and tubing size
• Pump head accepts continuous lengths of tubing for clean flow paths
• Dual-channel model delivers synchronous flow from two separate channels; single-channel model delivers highest flow rate
• Automatic tubing retention makes tube loading quick and easy
• Suitable for use with Masterflex® L/S® Digital Miniflex® Pump Systems

• Convex-roller design is gentler on live cells and shear-sensitive fluids—validated by independent test data
• Large-diameter rotor delivers higher flow rates at lower speeds
• Ensure the survival and vitality of live cells
• Flow rate 0.03 to 5700 ml/min with L/S tubing—flow rate depends on the drive rpm, pump head, and tubing size
• Compatible with all Masterflex L/S drives that accept two or more pump heads
• Models available for Masterflex L/S Precision and L/S High-Performance precision pump tubing
• 2-roller and 3-roller pump heads available--choose 2-roller for maximum flow, 3-roller for less pulsation

• Flow range of 1.8 to 220 ml/min—flow rate depends on drove rpm, pump head, and tubing size
• Pump head accepts continuous lengths of tubing for clean flow paths
• Dual-channel model delivers synchronous flow from two separate channels; single-channel model delivers highest flow rate
• Automatic tubing retention makes tube loading quick and easy

• Cartridges snap in and out for fast tubing changes—no need to remove pump head from the drive
• Load pump heads with 1 to 8 cartridges
• Mix large and small cartridges—one large cartridge occupies the same space as two small ones
• Flow rate 0.074 to 1700 ml/min with microbore or L/S tubing—flow rate depends on drive rpm, cartridge, and tubing size
• Accepts 1 to 8 small or 1 to 4 large cartridges
• Require drives with a minimum of 1⁄10 hp and a maximum of 600 rpm
• Constructed with stainless steel rotor and bearings with polysulfone ends

• Standard heads are precision molded to accommodate a single size of tubing
• Pump head is compact and simple in design with same side tubing entry/exit—perfect for space-limited applications
• Standard heads are compact and easy to integrate into your OEM applications
• Stack up to four heads depending on drive recommendations

• New design and automatic tubing retention allow for multiple tubing sizes—change tubing without removing head from drive
• Four-roller rotor improves pressure performance and mechanical stability while reducing pulsation
• Model available with integrated open-head sensor–connects directly to sensor-equipped drives
• Pump heads are stackable for multichannel applications
• Compact design for efficient use of space
• Suitable for use with L/S® Precision pump tubing sizes

• Standard heads are precision molded to accommodate a single size of tubing
• Pump head is compact and simple in design with same side tubing entry/exit—perfect for space-limited applications
• Standard heads are compact and easy to integrate into your OEM applications
• Stack up to four heads depending on drive recommendations

• Flow rate 0.04 to 19 LPM with I/P tubing—flow rate depends on drive rpm, pump head, and tubing size
• Digital interface with LED display shows pump rpm— confirm speed setting at a glance
• Remote control available using analog communication—voltage, current and contact closure
• Powerful motor lets you stack two pump heads for increased flow rate while offering ±0.25% speed control accuracy
• Membrane keypad allows for easy up-front control of speed, direction, and start/stop

Place motor and controller where convenient with modular design.

• Flow rate 0.0006 to 26 LPM with I/P tubing—flow rate depends on drive rpm, pump head, number of pump heads, and tubing size
• Digital interface with graphical LCD shows pump performance and operating mode— continuous run, timed dispense, copy dispense, or volume dispense
• Remote control available using analog communication—voltage, current and contact closure
• Select your preferred language from the user-friendly menu for programming and operation
• Dispense by Volume in ml (0.001 to 9,999 mL), L, or gal; Copy—1 to 9,999 dispense cycles; or Time—time interval of on/off cycles (1 sec to 99 hr, 59 min, 59 sec per cycle)
• Antidrip function ensures dispensing accuracy
• Brushless, maintenance-free motor offers ±0.1% speed control accuracy with a 6000 to 1 turndown ratio
• Reversible motor—purge tubing before or after pumping and pump fluid in either direction
• Powerful motor lets you stack two pump heads for increased flow rates and for multichannel applications

Networking drives offer either native EtherNet/IP™ or Profibus communication—no additional hardware or firmware required.